Maximum trolling depth with Scotty 1106

Squire

Well-Known Member
The article about Georgia Straight halibut got me thinking about trying something different during salmon non-retention between April 1st and July 15th. I find the idea of trolling just off bottom over some deeper sandy and gravel bottom areas intriguing.
The problem lies in how much line a Scotty 1106 can handle without crushing the spool. Scotty says 400’ but I know some guys offshore have fished that deep which would require still having some line on the spool so I’m asking if any of those guys have ways of mitigating this issue?
I had to get another spool of downrigger braid after snipping it off on the trim tab while I was trolling. I left about 100’ of the remainder on the downrigger and tied my new spool to it. I first pulled it all off and put one layer of black duct tape cut to size around the downrigger spool. Will this be enough to avoid the problem? I now have about 525’ of 200 lb test braid on the downrigger.
 
Braid or wire, they're not like mono. They have no stretch so no elastic compression to "crush the spool." The issue is to allow enough rim to keep the line from running off the edge. On a long retrieve, you may want to allow some cool-down time for the motor.
 
Braid has been known to spilt the spool especially on a hang up where it gets cinched. Do you have a spare set of spools you can set up with cable, and keep the braid set up? Or buy a set from Scotty with cable installed.
 
Just like a winch, you get the most pulling capacity with less line on the drum. Obviously a DR is a bit different as more line out means more drag, but running a 20 lb ball and 500’ of line could put a ton of load on the motor for the last 100’ in a strong current. That’s my theory at least.
 
I’m thinking of trying up to 400’ deep but wanted some line left on the spool once it’s down there. Good point about the extra load on the downrigger motor pulling that in. I plan to stick to the 15 lb ball but even that is a good pull from 230’ which is about the max I’ve been trolling at so far. The 1106 takes about as long to pull that up as it takes to reel in the gear once you pop it out of the clip.
And because the diameter is greater on the spool the last 150’ or so is pulled up at an essentially higher gear which could warm up the motor. This would also mean it’s always working harder at regular depths as well with the extra line on the spool. Hmmm…
 
Yes, the long-standing quip is that when you check your gear at the 200 foot level with the 1106 model, you can browse your email and read a chapter in a novel as you’re waiting for the cannonball.
 
Yes, the long-standing quip is that when you check your gear at the 200 foot level with the 1106 model, you can browse your email and read a chapter in a novel as you’re waiting for the cannonball.
But that's the downrigger that has the depth dial that actually works though right? I have a manual downrigger. At 200' it's a workout and the only thing I'm reading is that counter......for a long long time....
 
I was helping a friend spool up braid on his downriggers with a 2000 yard service spool. after 5 mins or so, I asked how much line do you want to put on here????>?! probably had 1500 ft on the rigger....
I regularly fish 300ft deep, sometimes having all 400ft of cable out. I use 20lb balls and hp riggers.. but I see no reason why you couldn't use 15lb balls, 150 lb braid and troll with the current, just tighten up the roll on a herring so you can troll slowly. but I suspect your going to find a lot of dogfish
 
I load 400' 250lb braid and I find its impractical to attempt any actual depth below about 250', with a 15lb ball, at 2 to 3 knots. Just too much drag, and the angle of the dangle is too damned high.
 
The article about Georgia Straight halibut got me thinking about trying something different during salmon non-retention between April 1st and July 15th. I find the idea of trolling just off bottom over some deeper sandy and gravel bottom areas intriguing.
The problem lies in how much line a Scotty 1106 can handle without crushing the spool. Scotty says 400’ but I know some guys offshore have fished that deep which would require still having some line on the spool so I’m asking if any of those guys have ways of mitigating this issue?
I had to get another spool of downrigger braid after snipping it off on the trim tab while I was trolling. I left about 100’ of the remainder on the downrigger and tied my new spool to it. I first pulled it all off and put one layer of black duct tape cut to size around the downrigger spool. Will this be enough to avoid the problem? I now have about 525’ of 200 lb test braid on the downrigger.
I missed this article, where is it posted? Thanks?
 
I load 400' 250lb braid and I find its impractical to attempt any actual depth below about 250', with a 15lb ball, at 2 to 3 knots. Just too much drag, and the angle of the dangle is too damned high.
18's are the minimum if your going 150 plus on a regular basis, 15's just don't cut it at that depth, too much blow back. 20's if your consistently going 200 plus.
 
say if your going deep then really need to be on HP's 15lb with 150lb braid is what i'll be running if it don't work then i change it up also remember you can troll slow less than 2 mph your not having to run coho speed's ....
 
IMG_2424.JPGIMG_2424.JPGIMG_2425.JPGIMG_2426.JPGIMG_2427.JPGIMG_2428.JPG

150lb 16 strand braid does me also one of the reason's for making up the spool spacer in 1/8th thick or the 1/4" version to hopefully reduce the possible spool splitting
 
I run 400 feet of blue Scotty braid. I've fished springs at over 300' off shore. With the current only tack one direction then run back. 1106's with 15 pound balls. Don't turn.
 
Back
Top