REELFAST going on the market

[reelfast]

Health is the reason:

REELFAST
LOA 31.5
LWL 25

Reelfast was built to owners spec by ALMAR in Tacoma, WA during the summer/fall of 2006. To my knowledge, she remains the one and only center console fishing machine fabricated by this company. Her hull was built to mil-spec by their Navy certified aluminum welders and outfitted by the various technicians who were employed by this company.

She is being offered complete and turnkey ready to resume fishing. Included are:
- Two Scotty 1106 DRs
- Electric pot puller by Line Hauler
- Various rod holders
- 4 Mustang self inflates + 2 self inflates from West Marine
- Bag of PFDs from West Marine
- All mooring lines and fenders along with boat hooks

Long lists of build speciations are available to interested parties. When sold, she will come with all service records.

Please, only serious fishing people, thank you.

$90,000 USD FOB Sequim, WA

greg@reelfast.us

 

[JAC]

Should post it in the buy and sell fourm . Nice boat also what's the power and hours?

 

[reelfast]

twin Yamaha 150s <500 hrs.

Thanks for the tip JAC.

 

[finaddict]

Sorry to hear you are selling for all the wrong reasons RF. Hope your issue is minor and resolvable. best wishes.

 

[the fog ducker]

Gorgeous Boat ,
You will miss her im sure

fd

 

[Chasin' Dreams]

Wow very nice boat! Sorry to hear it's for sale for health reasons. Boat's a beauty I'm sure it will sell quick.
Do I see three VHF antennae up there?

 

[reelfast]

Do I see three VHF antennae up there?

VHF antenna: CB antenna (many commercial boats still use this): cell phone amplifier(never have lost a signal with an 8' antenna)

 

[reelfast]

seems that the full spec sheet i have, 3 pages, is too big for this list. but to give you some additional detail, here is the first page:

----------------------------------------------------------------------------------------------------

REELFAST
LOA 31.5
LWL 25

Reelfast was built to owners spec by ALMAR in Tacoma, WA during the summer/fall of 2006. To my knowledge, she remains the one and only center console fishing machine fabricated by this company. Her hull was built to mil-spec by their Navy certified aluminum welders and outfitted by the various technicians who were employed by this company.

Her one piece aluminum plate, 0.250, was precut and delivered ready to assemble on steel jigs which had been developed by ALMAR over the course of decades. Ahead of her time for an aluminum hulled vessel, she sports;

- Full length reverse chines,
- Performance lifting strakes,
- A fully welded bow stem,
- Double thickness ‘beaching plate’ that extends about 6’along the keel includes a water tight beaching door and ladder,
- Self- bailing cockpit deck
- Two below deck 60” fish boxes with overboard macerating pumps
- Fully enclosed marine head with 10g holding tank, Y valve and macerating pump
- Large underdeck dry storage
- Forward bench seating, with storage below
- Rear fold down seating
- 130g fuel tank
- Mounting platforms for downriggers and/or pot puller along with fused connection on both sides of the vessel
- Protected at marinas by onboard galvanic isolator, power cord included
- Three onboard marine grade battery chargers running off of shore power
- Remotely controlled GO light and 140 db dual trumpet horns are mounted topside
- EPIRB, manual release

A fully networked electronics suite, current in 2006 includes:

Electronics:
- Raymarine C80 MFD
- 2 KW raydome
- Sonar with P66 transducer
- Electronic compass
- Auto pilot
- Ray VHF with DSC
- Standalone Dragonfly with CHIRP added in 2015 provides redundant GPS
- Cell phone amplifier with separate 8’ antenna
- CB with separate 8’ antenna to listen in on the commercial operators
- Pirate comm headsets for crew communication linked to VHF

 

[reelfast]

page 2:

---------------------------------------------------------

The Hull:
- Hull bottom .250 marine grade aluminum
- Forward Port side boarding door to allow beaching
- Keel reinforced in the bow with double layer of aluminum for 6’, .250
- ACCON 202-8 8” pop-up or folding cleats
- Bottom foam hull insulation,
- Self-bailing aluminum deck w/ nonskid walking surface
- 2 scupper valves
- side storage trays
- aft deck flood light
- drain plug
- non-skid fore deck
- zinc on hull
- 2,000 gph bilge pump
- Deadrise 20 degrees aft
- Side height 36”.
- 2 Racor 320-rac fuel filters
- New bottom paint February 2015
- Hull polished and waxed April 2015
- All welding done by USN certified aluminum welders
- Built to MIL spec

Other features:
- Two under floor 60” fish boxes/storage compartments with separate overboard drains and macerating pumps
- One super large dry storage area forward
- One on deck storage box, not a dry box with seating on top
- Anchor locker with bow roller, rode 200’of ½” 3 strand nylon/20’ of ¼” chain and 22# Delta set fast anchor
- Raw water wash down with hose and nozzle
- 2 house and 1 start battery new in 2015
- 2 series 32 batteries to power the ‘trollin tabs’by Lenco 24v trolling motors
- Electric trim tabs, Lenco, 12”x12”
- 30 AMP shore power w/ cord and galvanic isolator
- Rear seating on fold down bench
- Standup running position at helm with bench seat
- Various storage lockers for the gear we all accumulate
- Side curtain all around

Other stuff:
- Go light with remote control
- Radar reflector
- Marine head Jabsco manual pump flushing head in compartment with10g holding tank, Y valve + macerating pump

 

[reelfast]

page 2:

---------------------------------------------------------

The Hull:
- Hull bottom .250 marine grade aluminum
- Forward Port side boarding door to allow beaching
- Keel reinforced in the bow with double layer of aluminum for 6’, .250
- ACCON 202-8 8” pop-up or folding cleats
- Bottom foam hull insulation,
- Self-bailing aluminum deck w/ nonskid walking surface
- 2 scupper valves
- side storage trays
- aft deck flood light
- drain plug
- non-skid fore deck
- zinc on hull
- 2,000 gph bilge pump
- Deadrise 20 degrees aft
- Side height 36”.
- 2 Racor 320-rac fuel filters
- New bottom paint February 2015
- Hull polished and waxed April 2015
- All welding done by USN certified aluminum welders
- Built to MIL spec

Other features:
- Two under floor 60” fish boxes/storage compartments with separate overboard drains and macerating pumps
- One super large dry storage area forward
- One on deck storage box, not a dry box with seating on top
- Anchor locker with bow roller, rode 200’of ½” 3 strand nylon/20’ of ¼” chain and 22# Delta set fast anchor
- Raw water wash down with hose and nozzle
- 2 house and 1 start battery new in 2015
- 2 series 32 batteries to power the ‘trollin tabs’by Lenco 24v trolling motors
- Electric trim tabs, Lenco, 12”x12”
- 30 AMP shore power w/ cord and galvanic isolator
- Rear seating on fold down bench
- Standup running position at helm with bench seat
- Various storage lockers for the gear we all accumulate
- Side curtain all around

Other stuff:
- Go light with remote control
- Radar reflector
- Marine head Jabsco manual pump flushing head in compartment with10g holding tank, Y valve + macerating pump